VHS

Reinforcing sleeves

for thin-walled tubes

Reinforcing sleeves
additional picture 1
additional picture 2

Reinforcing sleeves

for thin-walled tubes

SO Code: -
Art. no.: -

Technical details

d = tube inside diameter
Assembly:
Insert sleeve into tube up to the knurled edge. Use a hammer (plastic or hard rubber) to drive in the sleeve all the way. This will cause the knurled neck to be pressed into the inner wall of the tube and will secure the neck against being dislocated or falling out.

Information on which tube is recommended for use with reinforcing sleeves can be found in Section i under “Recommendations for stainless steel tubes”.

Documents

  • Assembly instructions cutting / clamping ring fitting Download
  • Technical information cutting ring fitting Download
Type (Cust.) Art. no. D1 d L CAD Legend
Type VHS-04 Art. no. 1029062 D1 2.5 d 4.0 L 15.5 CAD Download
pcs
Type VHS-05 Art. no. 1029064 D1 3.5 d 5.0 L 15.5 CAD Download
pcs
Type VHS-06 Art. no. 1029061 D1 4.5 d 6.0 L 15.5 CAD Download
pcs
Type VHS-07 Art. no. 1029111 D1 5.5 d 7.0 L 17.0 CAD Download
pcs
Type VHS-08 Art. no. 1029112 D1 6.5 d 8.0 L 17.0 CAD Download
pcs
Type VHS-09 Art. no. 1029109 D1 7.5 d 9.0 L 17.0 CAD Download
pcs
Type VHS-10 Art. no. 1029110 D1 8.5 d 10.0 L 17.0 CAD Download
pcs
Type VHS-11 Art. no. 1029108 D1 9.5 d 11.0 L 18.0 CAD Download
pcs
Type VHS-12 Art. no. 1029103 D1 10.0 d 12.0 L 18.0 CAD Download
pcs
Type VHS-13 Art. no. 1029107 D1 11.5 d 13.0 L 18.0 CAD Download
pcs
Type VHS-14 Art. no. 1029101 D1 12.0 d 14.0 L 18.0 CAD Download
pcs
Type VHS-15 Art. no. 1029100 D1 13.0 d 15.0 L 18.0 CAD Download
pcs
Type VHS-16 Art. no. 1029098 D1 14.0 d 16.0 L 22.0 CAD Download
pcs
Type VHS-17 Art. no. 1029096 D1 15.0 d 17.0 L 22.0 CAD Download
pcs
Type VHS-18 Art. no. 1029097 D1 16.0 d 18.0 L 22.0 CAD Download
pcs
Type VHS-19 Art. no. 1029094 D1 17.0 d 19.0 L 18.0 CAD Download
pcs
Type VHS-20 Art. no. 1029095 D1 18.0 d 20.0 L 18.0 CAD Download
pcs
Type VHS-21 Art. no. 1030955 D1 19.0 d 21.0 L 21.5 CAD Download
pcs
Type VHS-22 Art. no. 1029011 D1 20.0 d 22.0 L 24.0 CAD Download
pcs
Type VHS-24 Art. no. 1029009 D1 22.0 d 24.0 L 18.0 CAD Download
pcs
Type VHS-25 Art. no. 1029010 D1 23.0 d 25.0 L 18.0 CAD Download
pcs
Type VHS-31 Art. no. 1029006 D1 28.5 d 31.0 L 18.0 CAD Download
pcs
Type VHS-32 Art. no. 1029008 D1 29.5 d 32.0 L 23.0 CAD Download
pcs
Type VHS-33 Art. no. 1029007 D1 30.0 d 33.0 L 23.0 CAD Download
pcs
Type VHS-38 Art. no. 1029005 D1 35.5 d 38.0 L 24.0 CAD Download
pcs
Assembly:
Insert sleeve into tube up to the knurled edge. Use a hammer (plastic or hard rubber) to drive in the sleeve all the way. This will cause the knurled neck to be pressed into the inner wall of the tube and will secure the neck against being dislocated or falling out.

Information on which tube is recommended for use with reinforcing sleeves can be found in Section i under “Recommendations for stainless steel tubes”.

Documents

  • Assembly instructions cutting / clamping ring fitting Download
  • Technical information cutting ring fitting Download
  • Data sheet Language: de
  • Data sheet Language: en